Shock Resistant Shock-resistant construction protects against impact and vibration. Solar Power A solar cell provides power for operation. Atomic time keeping. Charges in sun light or indoors.
Atomic Watch This watch receives time calibration radio signals that keep the displayed time accurate. World Time Displays the current time in 30 major cities and specific areas around the world. Stopwatch Accurate measurement of elapsed time with the touch of a button. The fraction indicates the unit of measurement, while the time figure indicates the maximum time measurement.
Daily Alarm, Hourly Time Signal. The daily alarm sounds each day at the time you set. The hourly time signal causes the watch to beep every hour on the hour. Snooze Feature Each time you stop the alarm, it sounds again after a few minutes. Battery Level Indicator Indicator shows the current battery level. Full Auto Calendar Allowances are made automatically for months of different lengths, in case date corrections for leap years are required.
Mineral Glass Hard glass resists scratching. Resin Band. Take care that you do not perform any button operations or move the watch during this time. If you use the watch in Japan or Europe each of which has two different transmitter locations , it will try to receive the time calibration signal from one of the transmitters in your current location.
If it cannot receive the signal, it will then try to receive the time calibration signal from the other transmitter. Radio interference may also cause problems with reception. Mainflingen Germany or Rugby England transmitters: kilometers miles.
The watch receives the time calibration signal automatically up to six times a day. The reception schedule calibration times depends on your currently selected Home City, and whether standard time or Daylight Saving Time is selected for your Home City.
Reception is not performed if a calibration time is reached while you are configuring settings. Before going to bed for the night, remove the watch from your wrist, and put it in a location where it can receive the signal easily. Avoid performing any button operation within five minutes before or after any one of the calibration times. Doing so can interfere with correct calibration. The receive operation will be performed whenever the display shows any one of the calibration times, regardless of whether or not the displayed time actually is the correct time.
The receiving indicator shows the strength of the calibration signal being received. For best reception, be sure to keep the watch in a location where signal strength is strongest. During signal reception, a transmitter indicator will flash to show you which signal is currently being received by the watch.
After signal reception is complete, the indicator of the transmitter from which the signal was received will remain on, without flashing. The time of the first auto receive operation of a new day depends on your currently selected Home City. Hold down A until the current auto receive setting ON. Press Ato exit the setting screen. Welcome to ManualMachine. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. AWG 1A. Keep the watch exposed to bright light Bright Light The electricity generated by the solar cell of the watch is stored by a built-in battery. Leaving or using the watch where l l l l l l l l l l l it is not exposed to light causes the battery to run down. Make sure the watch is exposed to light as much as possible. Battery charges in the light.
You can also perform manual receive or you can set the time manually. After that,. To display the digital time and last signal screens. In the Timekeeping Mode, press. The last signal screens show the date and time of the last successful time calibration. If time calibration signal reception has not been successful since the battery level dropped to Level 4 or since the battery was replaced,.
Last Signal Screens. The last signal screens continue to cycle on the display for about one or two. After that, the Timekeeping Mode screen reappears. Time Calibration Signal Reception. There are two different methods you can use to receive the time calibration signal:.
Auto Receive. With auto receive, the watch automatically picks up the time calibration signal four times a day at midnight, a. Manual Receive. Manual receive lets you start a time calibration signal reception with the press of a button. Make sure there are no metal objects nearby. The watch should not be on its side or facing the wrong way. Resin Band. Metal Band. G-Shock manuals. Text mode Original mode 1 2 3 4 5.
Timekeeping Mode Press C. Day Current Time Setting This watch automatically adjusts its digital time setting in accordance with a time calibration signal. Because of this, the analog time setting is automatically adjusted whenever you change the digital setting. To set your Home City 1.
In the Timekeeping Mode, hold down A until the city code starts to flash, which indicates the setting screen.
0コメント